Charred framing that looks solid but is not
We probe char depth with an awl and thermal imaging camera, then replace any board that fails the section check. New lumber goes in to match the original load path and is nailed to current California code.
Structural Repair After Fire SOLANA BEACH CA is the rebuild phase that makes a fire-damaged house safe and sellable again. We handle charred framing, roof sheathing, melted wiring and smoke-sealed drywall for homeowners and landlords across Solana Beach, CA. If your adjuster has approved the scope and you need a licensed crew that works to California code, call (833) 929-6186 and we will walk the damage with you.

Structural Repair After Fire SOLANA BEACH CA is the licensed construction phase that replaces what the fire weakened: charred studs, cracked drywall, heat-damaged roof sheathing, melted wiring and smoke-soaked insulation. It starts with a room-by-room assessment using a moisture meter and thermal imaging camera to find hidden heat damage and water from firefighting, then moves into framing, sheathing, drywall and finish work. We document every step for your insurance file, because the rebuild is usually the largest line item on a fire claim.
In Solana Beach, most of our structural calls come from kitchen and attic fires in older wood-frame homes, plus electrical fires in condos near the coast. Salt air and marine humidity make smoke odor and mold growth after fire worse if the rebuild waits, so we schedule fire structural restoration SOLANA BEACH quickly once the fire marshal releases the property. If you are searching for structural repair after fire near me in SOLANA BEACH CA, we are the crew that handles the framing and drywall, not just the cleanup.
Our structural repair scope covers the framing, sheathing, drywall, roofing and finish work needed to make the house safe and code-compliant again. Cleanup, odor removal and contents handling are separate scopes we can run on the same schedule if your carrier approves them. Here is what is in the rebuild contract.
We replace charred studs, joists, rafters and roof sheathing with lumber sized to the original load path. Every replaced board is photographed and logged for the insurance file.
New drywall, thermal insulation, tape, texture and paint go back in after rough-in inspections pass. We match existing texture and paint color so the rebuilt room blends with the rest of the house.
Fire damaged roof structural repair SOLANA BEACH work includes sheathing replacement, fascia and soffit repair, and re-roofing to coastal wildfire-zone requirements. We tarp the roof the same day to keep rain out.
Melted wiring and heat-damaged plumbing get replaced and inspected before drywall closes the walls. We coordinate the electrical and plumbing subs so the framing crew is not waiting on them.
Every rebuilt cavity gets smoke sealant and fire retardant coatings before drywall goes back. That step is what keeps soot residue and smoke odor from bleeding through fresh paint six months later.
We pull the structural permit, meet the city inspector on site and correct any punch-list items. You get a binder with permits, photos and warranty paperwork at the final walkthrough.
We walk the property with a moisture meter and thermal imaging camera, mapping char depth, heat damage behind intact drywall and water from firefighting. You get a written scope and photo report within 24 hours, and we flag anything the adjuster missed so it can be added to the claim before work starts.
We pull the structural permit through the California Contractors State License Board-licensed contractor on the job and secure the roof and windows with plywood and tarps the same day. If rain is coming off the Pacific, that tarp-over happens before we leave the property.
Charred lumber, cracked drywall and smoke-soaked insulation come out, then new framing goes in to match the original load path. We use DeWalt and Ryobi cordless tools for tight interior work and keep a HEPA air scrubber running so dust does not spread through the rest of the house.
Electrical, plumbing and HVAC rough-ins are inspected before drywall closes the walls. Then new drywall, insulation and smoke sealant go in, followed by tape, texture and paint. Most rooms sit 3 to 5 days in this phase depending on square footage.
We meet the city inspector on site, correct any punch-list items, and hand you a binder with permits, photos and warranty paperwork. The final walkthrough takes about an hour, and we do not call the job done until you have walked every room with us.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Finds heat damage behind intact drywall and hidden water from firefighting before demolition starts. It is how we catch charred framing the adjuster's walkthrough missed.
Reads moisture content in framing and insulation daily after water extraction. We do not close a wall until the reading matches dry standard.
Keeps dust and soot particles out of the rest of the house during demolition and framing. It runs continuously while the crew is cutting.
Dries framing and subfloor after firefighting water soaks in. We set them the same day as board-up and meter the structure until it reads dry.
Neutralizes smoke odor inside wall cavities and ductwork. We run them after framing and before drywall so the smell does not come back through paint.
Cleans char off framing without gouging the wood, which sometimes saves a stud that would otherwise be replaced. On Solana Beach rebuilds that can cut framing cost by 15 to 20 percent.
Used for tight interior framing, drywall and trim work where a corded tool is a trip hazard. The crew carries both brands on every truck.
A grease fire charred two studs and the ceiling joists behind the cabinets in a 1970s wood-frame home. The drywall was cracked and the insulation was smoke-soaked. The homeowner had a cleanup estimate but no structural scope.
We replaced the studs and joists, re-insulated the wall, rebuilt the cabinet run and repainted. The permit closed in 11 days and the adjuster approved the supplement on the first review. Total structural cost came in at $14,200.
An attic fire during a Santa Ana wind event burned through roof sheathing over the back bedroom and charred three rafters. The roof was open to the weather and rain was forecast in 48 hours.
We tarped the roof the same night, replaced sheathing, rafters and fascia, and re-roofed to coastal wildfire-zone spec. The roof was watertight in 10 days and the attic was re-insulated to current code. Structural cost was $38,500.
An electrical fire melted wiring in the shared wall between two condo units. The drywall was cracked on both sides and the HOA had not yet approved access for repairs.
We coordinated access with the HOA, cut and tagged the damaged circuits, rebuilt the shared wall cavity and re-ran wiring to code. Both units passed inspection on the first walkthrough in 16 days. Structural cost was $22,800 split between two carriers.
A fire weakens more than the room where it started. These are the structural problems we find most often on Solana Beach rebuilds, and what happens if they are left alone.
Ask a pro →We probe char depth with an awl and thermal imaging camera, then replace any board that fails the section check. New lumber goes in to match the original load path and is nailed to current California code.
We extract standing water, set Dri-Eaz air movers and dehumidifiers, and meter the framing daily until it reads dry. Only then does new drywall and insulation go back in.
We run hydroxyl generators and thermal foggers, seal the cavities with smoke sealant, and verify with a sniff test before drywall closes. Odor removal after fire is part of the rebuild, not an afterthought.
We open the wall, cut and tag the damaged circuits, and re-run wiring to current California Electrical Code. The electrical rough-in is inspected before drywall goes back.
Typical 2026 pricing in this area runs $8,000 to $45,000 for a single-room structural rebuild, and $60,000 and up for a whole-house framing and roof replacement. Cost depends on square footage, how much framing is charred, roof pitch and whether the electrical and plumbing have to be re-run. We give you a written line-item scope before any work starts so you can compare it to your adjuster's estimate.
We do, and we are licensed through the California Contractors State License Board with IICRC FSRT certified technicians on staff. We handle framing, sheathing, drywall, roofing and finish work for fire-damaged homes across Solana Beach, Del Mar Shores and Lomas Santa Fe. Call (833) 929-6186 and we will walk the damage with you and your adjuster.
A single-room rebuild usually takes 2 to 4 weeks from permit to final inspection. A whole-house structural rebuild runs 8 to 16 weeks depending on permit speed with the city and how long the framing and roofing packages take to arrive. We give you a written schedule at the start and update it weekly so you know when you can move back in.
Yes, in most cases dwelling coverage pays for structural repair after a fire, including framing, drywall, roofing and the permits to do the work. We bill carriers directly, photograph every replaced board and file supplements when the adjuster's scope misses hidden damage. Read your policy's dwelling limit and loss-of-use coverage before the first walkthrough so you know what is covered.
We are licensed, insured and IICRC certified, and we give you a written line-item scope before any work starts. Call (833) 929-6186 and we will walk the damage with you and your adjuster, usually within 24 hours.
Call for Assessment (833) 929-6186 →Fire losses do not keep business hours, and neither does our phone line. Call (833) 929-6186 any time, day or night, and describe what happened. We will ask about the rooms involved and the state of the roof and utilities, then dispatch a crew with board-up materials and extraction gear. Most emergency calls in Solana Beach get a tech on site the same day.