Soot, smoke, and wiring damage handled by licensed technicians

Electrical Fire Cleanup SOLANA BEACH CA

Electrical Fire Cleanup SOLANA BEACH CA starts with a full safety assessment, not a shop vac. We shut down damaged circuits, contain soot residue, and pull smoke out of drywall and insulation before it sets. If your panel, outlet, or attic wiring caught fire, our electrical fire damage restoration SOLANA BEACH crew is on call 24/7 across San Diego County. Call (833) 929-6186 and we roll a truck to 92075 or 92014.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Fire Damage Restoration Solana Beach — your local Fire Damage Restoration team
Careful work. Honest options.
About this service

Electrical Fire Cleanup SOLANA BEACH CA

Electrical Fire Cleanup SOLANA BEACH CA is a specialized restoration service that removes soot, char, smoke odor, and contaminated insulation after a wiring, panel, or outlet fire. It is not the same as general house cleaning. Electrical fires leave behind fine carbon residue that carries a charge and can re-ignite if the circuit is not isolated first. Our technicians cut power to the affected zone, test for residual heat with a thermal imaging camera, and then begin dry removal of soot before any wet cleaning touches the surface.

Most Solana Beach electrical fires start small and hide: a scorched outlet behind a couch, a melted junction box in the attic, a panel that arced during a November wind event. By the time you smell it, smoke has already traveled through wall cavities and into the HVAC return. That is why we treat every call as a full envelope problem, not a single-room wipe-down. If you are searching for electrical fire cleanup near me in SOLANA BEACH CA at 2 a.m., we answer and dispatch.

  • ✓ Stop Corrosive Soot Damage
  • ✓ Clear Smoke Odor at the Source
  • ✓ Document Everything for Insurance
  • ✓ Prevent Mold After Firefighting
What's included

What Electrical Fire Cleanup Includes

Every job starts with a safety assessment and a written scope. The inclusions below are standard on every electrical fire cleanup we run in Solana Beach. Structural repairs, panel replacement, and full rewiring are scoped separately with the licensed electrician so you see the cost of each piece.

✓

Circuit Isolation and Safety Check

We confirm the affected circuit is dead and check adjacent circuits for heat damage before anyone enters the space. Thermal imaging confirms no hidden hot spots remain in the wall cavity.

✓

Dry Soot and Char Removal

HEPA vacuums and soot sponges remove loose residue before wet cleaning. Charred drywall, insulation, and lumber are bagged and removed per California disposal rules.

✓

Smoke Odor Treatment

Thermal fogging and hydroxyl generation treat wall cavities and the HVAC system. Air scrubbers run continuously until odor testing passes at the final walkthrough.

✓

Water Extraction and Drying

Hose and extinguisher water gets extracted, and air movers and dehumidifiers dry the framing. We meter daily until the structure reads dry, which usually takes two to four days.

✓

Documentation Package

Photos, moisture readings, and a written scope go to you and your adjuster. This is the package that supports your claim and satisfies the city inspector at final.

How it works

What to Expect During Cleanup

01

Emergency Response

You call (833) 929-6186 and we ask three questions: is the power off, is anyone hurt, and what burned. We dispatch a crew and give you an arrival window. On arrival we confirm the circuit is dead, tape off the affected zone, and document the scene before anything is moved.

02

Safety and Scope Assessment

A technician walks the structure with a thermal imaging camera and moisture meter to map where heat and water traveled. We check the panel, the attic, and the wall cavities around the origin. You get a written scope the same day, usually within two to three hours on site.

03

Dry Soot Removal

We remove loose soot with HEPA vacuums and soot sponges before any liquid touches the surface. Charred drywall, insulation, and lumber come out and get bagged. This phase typically takes one to two days depending on how far smoke traveled through the return air system.

04

Wet Cleaning and Deodorization

Surfaces get cleaned with the right agent for the material, then we run thermal foggers and hydroxyl generators to neutralize odor in cavities. Air scrubbers run continuously. This is the phase that decides whether your house still smells like a fire three months from now.

05

Verification and Walkthrough

We meter the structure for moisture, sniff-test the rooms, and walk you through every repaired area. You get before-and-after photos and the documentation package for your insurer. Final walkthrough happens the same day the last air scrubber leaves.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Thermal Imaging Camera

Maps heat damage in wall cavities and confirms no hot spots remain before the structure is opened or closed.

HEPA Air Scrubber

Filters fine carbon and smoke particles out of the air during removal and drying, protecting the rest of the house.

Thermal Fogger

Pushes deodorizing agent into wall cavities and ductwork where smoke residue hides out of reach.

Hydroxyl Generator

Neutralizes smoke odor safely in occupied spaces without the ozone risk of older equipment.

Dry Ice Blaster

Removes stubborn soot from framing and masonry without water, which prevents smearing and secondary damage.

Moisture Meter

Reads moisture in drywall, lumber, and flooring so we know when the structure is actually dry, not just dry to the touch.

Dri-Eaz and Phoenix Dehumidifiers

Pulls moisture out of the air and framing after firefighting water so mold does not get a foothold.

Real results

Before and after.

Outlet Fire in a Town Center Condo

Before

An outlet behind a living room TV arced and burned a two-foot section of drywall. Soot stained the wall and ceiling, and the smoke smell had reached the bedroom. The breaker had tripped but the circuit was still suspect.

After

We isolated the circuit, removed the charred drywall and insulation, treated the cavity with a thermal fogger, and ran air scrubbers for 48 hours. The wall was repaired and painted, and the electrician replaced the outlet and checked the run. Final walkthrough passed on day four.

Garage Panel Fire in Lomas Santa Fe

Before

A panel fire in the garage sent smoke through the return air system and into every room. Firefighting water soaked the garage floor and the base of the adjacent wall. The family was out of the house and the insurer needed documentation fast.

After

We extracted the water, removed soot from the garage and adjacent rooms, treated the HVAC system, and ran hydroxyl generators for five days. Moisture readings returned to dry standard on day three. The panel was replaced by a licensed electrician, and the claim was approved with our photo log.

Attic Junction Box Fire in Eden Gardens

Before

A junction box in the attic burned insulation and scorched the roof deck above a bedroom. The homeowner noticed a burning smell but no visible flames. Insulation in a 10-foot radius was contaminated with soot.

After

We removed the burned insulation, cleaned and sealed the roof deck, treated the attic with a thermal fogger, and coordinated structural repair for two charred rafters. The attic passed inspection on day nine, and the bedroom below was cleared for occupancy.

Problems we solve

Problems We Solve After an Electrical Fire

The fire is out, but the damage keeps working. These are the problems we see most often in Solana Beach after a wiring or panel fire, and how we stop them before they cost you more.

Ask a pro →
01

Acidic soot etching metal and glass

We remove soot dry with HEPA vacuums and soot sponges, then neutralize the residue on hard surfaces. Electronics and fixtures get documented and cleaned before corrosion sets in.

↗
02

Smoke odor returning after cleanup

We treat cavities with thermal foggers and hydroxyl generators before the walls close. Odor testing at the final walkthrough confirms the treatment worked, not just that the room smells better that day.

↗
03

Mold growth from firefighting water

We extract standing water, set air movers and dehumidifiers, and meter the structure daily. Drying is documented so your adjuster sees the structure was returned to dry standard.

↗
04

Unsafe wiring left in place

We coordinate with a licensed electrician to verify and repair the circuit before power is restored. Panel and wiring upgrades are scoped and permitted separately so the fix is code-correct.

↗
Proof you can check

Licensed, Certified, and Documented

✓
IICRC Certified FirmInstitute of Inspection, Cleaning and Restoration Certification
✓
IICRC FSRT (Fire and Smoke Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
EPA Lead-Safe CertifiedU.S. Environmental Protection Agency
✓
California Contractors State License Board (CSLB) LicenseCalifornia Contractors State License Board
Good questions

Frequently Asked Questions

(833) 929-6186 →

Most electrical fire cleanup jobs in Solana Beach run $1,800 to $6,500 in 2026, depending on how far smoke traveled and whether wall cavities need to be opened. A single-room outlet fire with light soot is on the low end. A panel fire that pushed smoke through the HVAC system and soaked insulation is on the high end. We give you a written scope before work begins so you can compare it to your insurance estimate.

Fire Damage Restoration Solana Beach does. We are a local crew serving 92075, 92014, and the surrounding San Diego County neighborhoods, and we handle both the cleanup and the structural repair. Call (833) 929-6186 and we will confirm availability and give you an arrival window, usually within two to four hours for emergency calls.

Yes, in most cases. The key is sequencing: the circuit must be verified dead by a licensed electrician before anyone touches the char, and the structure must be metered for moisture before drywall goes back up. We coordinate with the electrician, remove contaminated material, treat the cavities, and document the repair so your insurer and the city inspector both sign off. Homes with aluminum wiring or an outdated panel get flagged for upgrade before we close the walls.

A single-room outlet fire typically takes two to four days from emergency response to final walkthrough. A panel fire or an attic fire that spread smoke through the return air system usually runs seven to fourteen days, mostly because of deodorization and drying time. Structural repairs, if needed, add time on top of that. We give you a day-by-day schedule after the scope assessment so you can plan where to stay.

Ready when you are

Call for Electrical Fire Cleanup SOLANA BEACH CA

One call gets a licensed crew moving toward your door. We answer 24/7, give you a real arrival window, and hand you a written scope before work begins. Call (833) 929-6186 now.

Call Now (833) 929-6186 →
Request an appointment

Call Our SOLANA BEACH Fire Damage Crew

Fire losses do not keep business hours, and neither does our phone line. Call (833) 929-6186 any time, day or night, and describe what happened. We will ask about the rooms involved and the state of the roof and utilities, then dispatch a crew with board-up materials and extraction gear. Most emergency calls in Solana Beach get a tech on site the same day.

Request received — our team will be in touch shortly.
Tap to call(833) 929-6186